
Paver sealing for Cedar Hills homes
Paver Sealing in Cedar Hills, FL
Cedar Hills sits along the Cedar River, and a fresh seal keeps driveways and walks tidy, so call (904) 817-0508.
- Brings out deeper paver color
- Fresh joint sand helps lock pavers in place
- Gives weeds less room to grow
- Makes the surface easier to keep clean
- Free estimate, no obligation
Request a Free Estimate
Free, no obligation.
Fast, careful paver sealing in Cedar Hills
Paver sealing in Cedar Hills begins with a free visit from a local contractor. Work includes driveways, front walks, patios and pool decks, with cleaning, new sand and sealer, from the streets by Blanding Boulevard to the blocks near the Cedar River. Send your request when you ask for a free estimate, and a contractor replies within 1 business day, usually much sooner.
Most of these brick and block ranch houses went up in the 1940s and 1950s, and many now have pavers that were added later. If yours have turned gray, with sand gone and weeds in the cracks, a wash, fresh sand and a new coat show right from the curb. Call (904) 817-0508 and say what you see.

Why hire a local paver sealing contractor in Cedar Hills?
The houses in Cedar Hills are mid-century, and their driveways have often seen decades of rain, roots and repairs. A local paver contractor has seen that mix, so ask for a free estimate and talk through your lot.
A free look, no pressure
Someone comes to the house, looks at the drive and walk, and gives you a price. You can say no after that.
Numbers you can check yourself
Quotes in this area usually fall between $1.75 and $3.25 per square foot for washing, new sand and sealing. Ask what each line includes.
Finish to suit your street
Matte keeps the natural look beside a brick ranch house. A wet look deepens color but shows scuffs sooner.
You make the call
You pick the date and the finish. The estimate carries no obligation, and nothing starts until you say so.
Get Your Free Estimate in Cedar Hills
Tell us about your pavers in Cedar Hills.
Free, no obligation

What paver problems show up most in Cedar Hills?
Water that runs onto the wrong yard
In 2017 a Cedar Hills resident of more than 40 years told News4Jax that a blocked storm drain and ditch sent water onto nearby homes and caused the ground to cave in. Poor drainage like that can wash out the ground under a driveway. Pavers that sit in runoff can sink. Sealing does not fix a washout, so low spots are reset first. If water pools at the end of your drive, tell the contractor. A neighbor's ditch problem can become yours when water crosses the property line.
Sand ground and summer storms
USDA maps the Ortega soil series, first described in Duval County, as moderately well drained sand. Jacksonville also gets about 53 inches of rain a year, with the biggest rise in summer and autumn. Rain moves through sand fast and pulls joint sand along with it, so open joints are common after a wet July. When joints empty, weeds root and pavers rock, so sand goes back in before sealing. That one step keeps the surface steady for the next wet season. Sand also wicks moisture quickly, so a drive can look fine on top while the base is shifting underneath.
Fade after years of sun
Summer highs near 91 degrees and bright sun bleach color out of pavers. One Jacksonville company says bare concrete pavers fade noticeably in 3 to 5 years. Many Cedar Hills driveways are older than that, so a faded look is no surprise. A fresh seal cannot restore lost color completely, but it deepens what is left and slows more fading. A matte or satin finish keeps the look natural. Fade is gradual, so many owners do not notice it until a new section is laid beside an old one.
Old coats from past owners
Many houses here have changed hands since the 1950s, so a driveway may carry a coat nobody remembers, and a new owner rarely has the paperwork. Sealteam Jax says oil-based coats must be stripped first, which applies to about 10 to 20 percent of its jobs. Sealers of the two types do not mix, and water-based never goes on top of solvent-based. A peeling or cloudy surface is a clue that the old product needs attention. The contractor tests a small spot first. If the surface feels slick or looks glassy in patches, an older product may still be there.
Weeds in widened joints
Weeds appear where joints get wide and soil collects, according to a landscape trade group. Stabilizing the joint sand with sealer is the most effective way to stop them. Older pavers often have joints that opened over the years. Weeds are removed, sand is refilled and the sealer locks it in place, which keeps the weeds from coming right back. A wide joint also gives ants a way in, which is another reason to refill and lock the sand.
Does paver care differ in the older streets of Cedar Hills?
Yes, a little, because the area was built mostly in the 1940s and 1950s. Cedar Hills runs from Blanding Boulevard on the east to Lane Avenue on the west, with about 3,000 single-family brick or concrete block homes. Driveways tend to be shorter and walks narrower than in newer suburbs, which can mean a quicker job. Tell the contractor your street when you ask for a free estimate.
Street names are a local clue. Cedar Hills uses a cartoon theme, with Mother Goose Road, Peter Pan Place and Flopsy, Mopsy and Cotton Tail lanes. Homes in Cedar Hills Estates that were listed or sold recently were built between 1955 and 1971, with a median of 1960, and sizes run from 910 to 3,248 square feet. Call (904) 817-0508 and name your street.
Many listings in Cedar Hills Estates say there is no HOA. That means you may not need anyone's sign-off on a finish, though your deed or a street covenant can still hold rules. Florida law limits an association's review to what its own documents state. Check your paperwork, then ask for a free estimate.
Pool decks are common behind these older houses, and they ask for a little more care. Splash, sunscreen and chlorine film build up on the surface. A finish with some grip is worth asking about near water. Call (904) 817-0508 and say whether your pavers sit beside a pool.
What does paver sealing cost in Cedar Hills?
Rates published for the region run $1.75 to $3.25 per square foot to clean, sand and seal pavers, and Safe Touch notes that a failed coat costs extra to strip. The joints are inspected before the price is set. In Cedar Hills the things that move your number are empty joints, old sealer and a sunken edge. To put a number on your Cedar Hills pavers, ask for a free estimate.
Smaller jobs cost more per square foot because prep does not shrink with the size of the surface. A short driveway and a front walk may cost more per foot than a long drive. That is normal, and it is a reason to bundle surfaces in one visit. Call (904) 817-0508 and list everything you want done.
Ask what the quote covers before you compare totals. Look for washing, joint sand, the coat count and the finish, each named on its own line. Two bids that look far apart often leave out different steps, so a written scope shows where the gap comes from. To get one, ask for a free estimate.
| Paved area | Typical example | Clean, sand and seal |
|---|---|---|
| 300 sq ft | Small patio or walkway | $525 to $975 |
| 600 sq ft | Two car driveway | $1,050 to $1,950 |
| 1,000 sq ft | Large driveway or pool deck | $1,750 to $3,250 |
| 1,500 sq ft | Driveway plus pool deck | $2,625 to $4,875 |
Math based on the $1.75 to $3.25 per square foot that Northeast Florida paver companies published as of November 2026. Your contractor sets the actual price after seeing the surface. Repairs, leveling and stripping failed sealer are usually extra.

How does a paver sealing job work in Cedar Hills?
Look at the drive and the drainage
The contractor walks the lot and watches how water leaves the driveway. If runoff from a neighbor reaches your drive, say so now. Pavers that have dropped or wobble get marked for resetting before anything else. A test spot shows what is on the surface, which matters because water-based sealer cannot go over solvent-based. The visit ends with a clear price, and the decision stays with you.
Wash it clean
Dirt, algae, oil and rust come off first. Deep oil or rust stains may not come out completely, and the contractor will say what is realistic. Brick walls and shrubs stay clear of runoff. Careful rinsing matters most beside older brick. Expect the surface to look darker while it is wet.
Wait for dry pavers
Pavers need to dry out fully, and the sealer waits until they do. A shaded walk can take longer than a sunny drive. If the surface is still damp, the visit simply moves to the next dry day. A cloudy finish is the price of rushing. A walk in the shade can need an extra day, and that is normal.
Put sand back
Sand lost in the wash is replaced, swept into each joint and packed tight. Full joints stop pavers from rocking and keep weeds out. A sand color near the paver shade looks clean and even. That is how the surface ends up looking tight and neat. Joint sand color is the detail neighbors notice from the street.
Seal and let it cure
The final step is spray, then roll, which spreads the coat evenly and works it between the pavers. Allow a few hours before anyone walks on it and about a day before cars. Rain landing on a new coat can ruin it. Before the job closes you walk the surface, and any missed spot is fixed on the spot. Keep the car on the street until the contractor clears the drive.
Complete paver services in Cedar Hills
Expect four steps in a set order. The surface is washed, left to dry, topped up with new joint sand and finally sealed with a spray and a roller. Short driveways may finish in a day, while larger layouts can take two. To plan yours, ask for a free estimate.
A Cedar Hills property may hold a driveway, a front walk, a patio and a pool deck. Drive lanes show tire marks, and pool decks pick up splash and sunscreen. Sunken edges are reset before any sealer goes on. Call (904) 817-0508 and list each surface, with a photo if you can.
Pick the finish and the sand color that suit the house. One Jacksonville company offers four finishes, from wet look high gloss to natural matte, and a low-contrast sand color makes the surface look clean. Sealer typically lasts two to five years, so the choice stays with you a while. To compare finishes, ask for a free estimate.
Fall and winter are drier, and summer storms can move a date. A coat needs a dry surface and about a day without rain, and cars stay off for about a day. When you ask for a free estimate, mention any date that matters, such as a party or a sale.
Questions to ask before you hire
- How do you handle the paver edges next to my lawn and landscape beds?
- Can you seal my pool deck and driveway on the same visit?
- Do you wash with a surface cleaner or a hand wand?
- Will you test a small spot of my pavers before you pick a sealer?
- Do you carry liability insurance, and can I see the certificate?
- What finish do you recommend for my pavers: matte, natural or wet look?
- What do you do if the sealer looks blotchy or peels later?
What do sealed pavers look like around Cedar Hills?









Why local matters in Cedar Hills
A contractor who works around the Westside knows mid-century lots, with short drives, mature trees and older walks. A quote written for a new subdivision would miss that. When you ask for a free estimate, the price reflects a 1950s lot, not a new one.
Drainage is a local worry. The 2017 storm drain trouble reported in Cedar Hills shows how water can move across yards. A local contractor asks where your water goes and plans around it, including how long to let the surface dry. Call (904) 817-0508 and mention any spots where water collects.
Local contractors also know the roads. Blanding Boulevard borders the east side, and the shopping center that opened in 1955 still stands nearby. A contractor can plan deliveries and parking around busy hours. To pick a time, ask for a free estimate.
One more point is access. Older streets can be narrow, and parked cars may line the curb. A contractor plans where to set up and where to keep the water and sand. Tell the contractor about steep drives or tight turns when you ask for a free estimate, and the visit goes smoother.
Cedar Hills has a long record as a place people stay, so neighbors compare notes. A contractor who does careful work on one driveway often hears from the next house. That matters when you are choosing someone for your own front walk. Call (904) 817-0508 and ask for the contractor's plan for your street.
What is Cedar Hills like for a homeowner?
It is an older neighborhood on the Westside, along the Cedar River across from Lake Shore. The Cedar Hills Shopping Center opened in 1955 as an early large shopping district outside Downtown, and it still stands at 282,000 square feet. About 3,000 homes fill the streets between Blanding Boulevard and Lane Avenue. To talk about your lot, ask for a free estimate.
ZIP 32210 counts 66,415 people and 26,199 households, so the area is busy and well settled. Long-time residents are easy to find, since one told News4Jax she had lived here more than 40 years. A fresh seal is a simple way to tidy the front of the house, and it makes the next wash easier. Dial (904) 817-0508 and ask for the free estimate.
Shade is part of the picture too. Where trees shade a yard, walks stay damp longer than sunny drives. Damp surfaces grow algae and take longer to dry before a coat. Mention the trees on your lot when you ask for a free estimate.
Street names give the place away, with Mother Goose Road, Peter Pan Place and Flopsy, Mopsy and Cotton Tail lanes. The cartoon theme is a quick way to tell the contractor where you live. Brick fronts and short drives make the pavers stand out from the curb. To mention your lane, ask for a free estimate.
Frequently Asked Questions
What is the average cost to seal pavers in Cedar Hills?
The published regional range is $1.75 to $3.25 per square foot to clean, sand and seal. Stripping a failed coat costs more. Your total follows the square footage and the condition. A free estimate gives a firm figure, and the contractor can explain what each line covers. A quote that lists each surface is easier to compare than a single lump figure.
How much does it cost to seal outdoor pavers like a Cedar Hills patio or walkway?
Small surfaces cost more per square foot, because prep does not shrink with size. A walkway and patio done with the driveway usually price better than a separate visit, since setup happens once. The same published range applies. Ask for the pieces to be listed on the quote. A patio next to a driveway is usually measured together.
How often should pavers be sealed in Florida, and in Cedar Hills?
Companies commonly quote two to five years between coats, which is a wide range. PaverGuard puts full-sun driveways near 18 to 24 months and shaded walkways at 24 to 36. Water that no longer beads up is the cue that it is time. The contractor can look at yours and give a rough date for the next coat. A cost guide puts most reseals at three to five years, with driveways nearer three.
Are pavers worth sealing in Florida, and is that true in Cedar Hills?
For most pavers, yes. Sealer slows fade, keeps oil from soaking in and holds joint sand. Cedar Hills has sandy ground and hard summer rain, so the sand protection counts, since sealer keeps the joints from emptying. One company says bare concrete pavers fade noticeably in 3 to 5 years. Mid-century driveways with old pavers often respond well to a fresh coat.
How long do paver sealers last in Cedar Hills?
Typically two to five years in Northeast Florida. Sun, foot traffic and shade all change that number. A cost guide says driveways run closer to three years. Your contractor can give a range for your surface, based on how it looks at the estimate. Your contractor can tell you which surfaces on your lot wear quickest.
Why is paver sealing so expensive in Cedar Hills?
Prep work is where the hours go, more than the product. One company says it spends 2 to 3 hours of prep for every hour of sealing. Washing, drying and sanding each take time, and drying cannot be rushed in humid weather. Stripping old sealer adds more. Stripping old sealer adds both time and product.
Do Cedar Hills homeowners need HOA approval to seal pavers?
Often not, since many listings in Cedar Hills Estates say there is no HOA. Check your deed to be sure. Florida law limits an association's review to what its own documents state. If you do have an HOA, a natural matte finish is the quieter choice, and you can ask the board in writing. A deed or covenant can still apply even when there is no formal HOA.
Can old or sunken pavers in Cedar Hills be sealed?
Sealed pavers lock in whatever condition they are in. Sunken or lifted sections are reset first, since sealing over them only keeps the problem. Deep oil or rust may not come out completely. The contractor will tell you what is realistic at the estimate, so you know before you decide. Dips and rocking pavers are reset first, since the sealer would hold them in that shape.
Ready for a Free Estimate in Cedar Hills?
Call (904) 817-0508 and tell us about your pavers.
Free, no obligation
